三级2017在线观看免费_婷婷色五丁香_亚洲天堂视频一区_国产无遮挡又黄又爽奶头_亚洲无码在线免费视频_舌吻哼哼唧唧原声不带歌_一级做a爰片毛片潮喷中文字幕无码精品_2020国产精品国产精品_脫了動漫美女內褲猛烈進入gif_人妻中文字字幕在线乱码

cRIO-9472
該設備還使用TRIG1啟動預觸發的DAQ操作。在大多數預觸發應用程序中，TRIG1由軟件觸發器生成。有關在預觸發DAQ操作中使用TRIG1和TRIG2的完整說明，請參閱TRIG2信號說明。TRIG2信號任何PFI引腳均可接收TRIG2信號作為輸入，該信號可作為PFI1/TRIG2引腳的輸出。TRIG2與DAQ序列的關系見圖4-10。作為輸入，TRIG2配置為邊緣檢測模式。您可以選擇任何PFI引腳作為TRIG2的源，并為上升沿或下降沿配置極性選擇。TRIG2的選定邊緣啟動預觸發DAQ序列的后觸發階段。在預觸發模式下，TRIG1信號啟動數據采集。掃描計數器（SC）指示識別TRIG2之前的小掃描次數。SC減至零后，將加載要采集的觸發后掃描數，同時繼續采集。如果在SC遞減為零之前斷言TRIG2，則設備忽略TRIG2。收到TRIG2的選定邊緣后，設備獲取固定數量的上升邊緣極性下降邊緣極性t w t w=10 ns小t w t w=25-50 ns第4章連接信號©National Instruments Corporation 4-21 NI PCI-6110/6111用戶手冊掃描和采集停止。此模式在接收TRIG2之前和之后都會獲取數據。作為輸出，TRIG2在預觸發采集序列中反映后觸發，即使另一個PFI正在外部觸發采集。TRIG2不用于后觸發數據采集。輸出為有源高脈沖，脈沖寬度為25至50 ns。該輸出在啟動時設置為高阻抗。圖4-13和4-14顯示了TRIG2的定時要求。

The device also uses TRIG1 to initiate pretriggered DAQ operations. In most pretriggered applications, TRIG1 is generated by a software trigger. Refer to the TRIG2 signal description for a complete description of the use of TRIG1 and TRIG2 in a pretriggered DAQ operation. TRIG2 Signal Any PFI pin can receive as an input the TRIG2 signal, which is available as an output on the PFI1/TRIG2 pin. Refer to Figure 4-10 for the relationship of TRIG2 to the DAQ sequence. As an input, TRIG2 is configured in the edge-detection mode. You can select any PFI pin as the source for TRIG2 and configure the polarity selection for either rising or falling edge. The selected edge of TRIG2 initiates the posttriggered phase of a pretriggered DAQ sequence. In pretriggered mode, the TRIG1 signal initiates the data acquisition. The scan counter (SC) indicates the minimum number of scans before TRIG2 can be recognized. After the SC decrements to zero, it is loaded with the number of posttrigger scans to acquire while the acquisition continues. The device ignores TRIG2 if it is asserted prior to the SC decrementing to zero. After the selected edge of TRIG2 is received, the device acquires a fixed number Rising-edge polarity Falling-edge polarity t w t w = 10 ns minimum t w t w = 25-50 ns Chapter 4 Connecting Signals © National Instruments Corporation 4-21 NI PCI-6110/6111 User Manual of scans and the acquisition stops. This mode acquires data both before and after receiving TRIG2. As an output, TRIG2 reflects the posttrigger in a pretriggered acquisition sequence even if another PFI is externally triggering the acquisition. TRIG2 is not used in posttriggered data acquisition. The output is an active high pulse with a pulse width of 25 to 50 ns. This output is set to high impedance at startup. Figures 4-13 and 4-14 show the timing requirements for TRIG2.